Bmw Fan Clutch Removal
I go over how to remove and install the mechanical fan on a BMW with the M52TU or M54 Engine.
Bmw fan clutch removal. Use an infrared temperature gun to measure the fan clutch temperature. When the air temperature reaches 88 degrees C 190 degrees F remove the plastic sheet. Adjustable Pin Spanner Wrench.
Dont waste your money on special tools to get the fan clutch off of the water pump. Metric Service Wrench Set 15 Pc. Metric Service Wrench Set 15 Pc.
Pay 0 APR for 6 Months. I show you how. Bmw roundel bmwcca bimmer beamer mike miller fan clutch blades diy how to tutorial seize Part 07129905536 BMW special tool 115030 115040 Fan shroud rivets Part 1711712963 Expansion tank cap seal Part 17111723580 bentley manual publishers pelican article newspaper friction test drag viscous fluid seized fan blades crack MTC hella behr kroil penetrating oil transmission hood.
Place open wrench on fan clutch nut 32mm combo wrench. Forward on nut to avoid hitting vanos body and radiator hose clamps. Previous Price C 3352.
Allows the technician to hold the water pump pulley in place while loosening the radiator fan for removal of the visco-coupling on the cooling fan. Add to Cart Add to My List. BMW Fan Clutch and Fan Removal and Installation.
BMW 36mm x 32mm Fan Clutch Nut Wrench Removal Thermo Viscous Fan Tool. Forward on nut to avoid hitting vanos body and thermostat hose connector. Remove fan fan clutch from water pump shaft.
Adjustable Pin Spanner Wrench 5 99. Some Z3 models may have an electric engine side-cooling fan. Pay special attention to the order of components you remove while getting to the fan clutch.
When re-fitting tighten clutch nut to 30 ftlb. Fan clutch disengagement should start to occur at 60 degrees to 79 degrees C 140 degrees F. I will note the difference as needed.
The car in this video is a 2000 Z3. Removes lock nuts on thermo Viscous fans found on Mercedes-Benz BMW and many Ford models. Add to Cart Add to My List.
I did the fan delete mod all i did is remove the fan clutch etc and fit a new lower temp fan switch on the side of the radiator an 88C one driven it hard including track days and no issues 3 years plus monitored the temps with INPA and rock steady as long as your cooling system is in top condition i would not hesitate I changed the pump the radiator and the expansion tank at the time too. Core charges are assigned to parts that have reusable components by manufacturers to encourage the return of the used units. Strongly strike wrench side at top with heavy hammer to break nut seize sledge.
Search Results For Fan Clutch Wrench 278 Items. Place open wrench on fan clutch nut 32mm combo wrench. A timing light and a good marker or piece of chalk are necessary for you to evaluate the fan clutchs condition and the nearby water pump bearings.
The cooling fan removal procedure differs slightly between 4 and 6-cylinder models. Remove engine cooling fan by holding the belt drive pulley with a suitable flat bar tool that fits over the top of the drive pulley attachment bolts then using a suitable flat spanner to unscrew the fan clutch assy clockwise. Top Rated Seller Top Rated Seller.
It looks like an aluminum UFO with fins around its body. 15 product ratings - BMW 32mm Fan Clutch Nut Wrench and Water Pump Holder Tool Kit Removal USA Ship 625 Trending at 975 Trending price is based on prices over last 90 days. The clutch is at the center of the fan assmbly and is engine driven via a poly-ribbed belt.
35 out of 5. I looked on various forums and. Remove fan fan clutch from water pump shaft.
Once you return the old part you will be. Then remove the shroud following the steps below. BMW Fan Clutch Delete Kit - E36FDMK 323i 323is 328i 328is M3 Z3 Save for later 1 Rating Available Ships in 1 business day.
A definite decrease of fan flow noise roaring should be noticed. Fan clutch of radiator cooling fan on your BMW e34 car is located in front of the engine behind the radiator. 32mm Fan Clutch Nut Wrench Water Pump Holder Removal Tool Kit Fit for BMW M4 M10 M20 M30 M40 M44 M50 M52 M52TU M54 M56 M60 M70 M73 S14 S38 S54 S50B30 S50B32 etc.
The fan clutch contains hydraulic oil which its viscosity varies upon the temperature. Hey this is for any of you that during various occasions have had to take the cooling fan out from the front of your inline-6 e36 to make room or change the waterpump but cant find a simple way to stop the damn waterpump pulley from rotating with the fan bolt. If you notice the water pump is squealing or acting funny you might want to replace that too.
Strongly strike wrench side at top with heavy hammer to break nut seize sledge hammer. Skip the steps where the viscous fan is removed. Remove fan belt static friction method.
